SAR Scenario Paratoo Mixed Passenger Freight V1

From TrainzOnline
Revision as of 14:20, 15 October 2022 by Pware (Talk | contribs)

(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search
ArrowLeftBtn.png   9   Peterborough to Paratoo Mixed Passenger Freight  ArrowRightBtn.png
A scenario in the SAR Peterborough Base Session
Mixed passenger and freight run from Peterborough to Paratoo. Bottom

 The Historical Bit 
The region between Peterborough and Broken Hill is very sparsely populated - cattle, mining and maintaining the railway were the major activities. Most, or in some cases all, of the houses at the settlements along the line were built for railway track workers and their families.

There was an express passenger service that ran from Port Pirie to Broken Hill but between Peterborough and Broken Hill it only stopped to load water and coal, and to change the loco and crew. Local stopping passenger services were usually provided by a passenger car attached to a freight service. This scenario replicates that service between Peterborough and Paratoo.


Mixed Passenger
 Era:  1920s to 1969
 Duration:  1 hour 40 minutes
 Loco:  SAR T 202 on Peterborough  Car Siding 
 Consist:  Attached to SAR T 202
The wagons have been placed in the order of their destinations with Paratoo and the passenger van at the rear end. Each wagon has its destination as part of its name e.g. QLX Paratoo indicating its destination is Paratoo.

Location Index

Each location in the layout has a detailed set of track diagrams that provide a variety of useful information

The  Getting Started  guide below gives a summary of what is available.

To display this information click any Location Index graphic, or go to the bottom of the page for all the session links (all links will open in this window).
Getting Started:
  1. If you have already closed the opening message window then the first step is to pause the session by pressing the  P  key.
  2. Next locate your loco. Either:-
    • Open the Finder Tool (press  Ctrl   F ) and type, in the Name field, the name of the loco, in this case SAR T 202 (or just T 202 should be enough). Click the tick icon, OR
    • Open the Driver List (bottom left of the screen) and then scroll through the list to find the loco name (SAR T 202) then click the drivers Eye icon Driver Eye.png to take control of the loco
  3. Take a few moments to get your bearings. Click Peterborough Data (this link will open in this window) to show the location details and track plans for Peterborough. In each location details page:-
    • the Tab HM White.png tab gives an overall summary of each location with a "potted" history (where available).
    • the Tab TM Grey.png tab reveals the invisible TM Track Marks for Drive To commands.
    • the Tab IN Grey.png tab lists all active industries and their commodities.
    • the Tab SW Grey.png tab describes the names, locations and settings of all junction switches as well as some switch sets you may want to use.
  4. Each location details page has direct links to the adjacent locations so you can explore along the route.
  5. When you are ready to start, reload the Peterborough Base Session page (click the Scenarios button on your current location page) and select this Scenario again or just use the Back button on your browser - whichever is quicker.
  6. Switch back to Driver Mode and either close the opening message window or press the  P  key to start the session.


Tutorial:
Tutorial A tutorial on using these scenarios is provided in the link on the left. The link will open in this window


Orders:
  1. Reverse the train out of the siding and onto the station line. Pull the train forward into Peterborough  Station  stopping with the passenger car alongside the station building.
  2. You have the authority to travel on the section Peterborough to Paratoo.
  3. Depart Peterborough at 08:06 and proceed to Paratoo stopping at Ucolta, Oodla Wirra and Nackara. At each stop place the passenger car alongside the station building.
  4. Detach and shunt wagons at each location as required. All wagons have been placed in the consist in destination order from the front. Position QLX wagons at the  Goods Sheds , MTW flat wagons at the  Goods Cranes . Leave each wagon at its unloading point.
  5. At Paratoo coal and water the loco as required.
  6. Option: Return the train to Peterborough collecting the wagons along the way.
Logo


Driving Notes:

A summary of the facilities and product loads at all locations along the line is provided in the link Port Pirie-Broken Hill Line

  • The approaches to all locations are protected by invisible signals to prevent the AI Half Speed Slowdown Problem when approaching a signal at stop.
  • Trackmarks and industries have been provided for AI Drive To Trackmark, Drive via Trackmark and Drive to  Industry  commands. Click Location Index for details.
  • An industry active station (where you can use the Drive To industry command) is at Peterborough. Industry active stations will have a longer than expected wait time.
  • Manual (no AI) driving is possible. As a visual driving aid, a Caution warning sign has been placed at the location of the Main Approach Dn and Main Approach Up trackmarks. Click Location Index for details.
  • If driving manually in yards, you are responsible for correctly setting any catch points.
Strip Map
Route Key

Links: All links will open in this window
ArrowLeftBtn.png Scenarios
Session Scenarios
Location Index
Location List
Tutorial
Drive Tutorial
Rolling Stock
Rolling Stock
Loco Roster
Loco Roster
Industries
Active Industries
Top ArrowRightBtn.png


This page was created by Trainz user pware in February 2021 and was last updated as shown below.


Personal tools