How to Use Navigation Point Rules (Applications)

From TrainzOnline
(Difference between revisions)
Jump to: navigation, search
(Trainz Creation Tutorials:)
m (Explanation)
Line 214: Line 214:
 
**'''Line 5: Wait''' A wait of 20 seconds then ...
 
**'''Line 5: Wait''' A wait of 20 seconds then ...
 
***'''Line 6: Driver Schedule''' The AI train is given commands to move to the next destination via the Main Line.
 
***'''Line 6: Driver Schedule''' The AI train is given commands to move to the next destination via the Main Line.
 +
----
 +
----
  
 
='''Trainz Wiki'''=
 
='''Trainz Wiki'''=

Revision as of 13:05, 6 June 2018

The screenshots shown below give examples of how navigation points can be used to control the operation of a session.

Contents

Application 1: Clearing Unused Navigation Sets

The Scenario

A user decides to ignore navigation points at a location and drives straight through. When the consist passes over a trigger the unused navigation point sets are removed.

Preconditions

Rules Used

Session Rules Screenshot

NavClearSets.JPG

Example Explanation

  • Line 1: Trigger Check the event is triggered by the consist leaving the location with the navigation points.
    • Line 2: Navigation Set Clear a navigation set is manually completed and any visible icons are removed. This can be performed on any sets that have already been completely or partially completed.

Lines 3 and 4 repeat the process for any other navigation sets.

Application 2: Checking for Incomplete Navigation Sets

The Scenario

A check is made to see if all the navigation points in a navigation set have been completed. If not then the set will be manually completed and a message displayed.

Preconditions

Rules Used

Session Rules Screenshot

NavSetCheck.JPG

Example Explanation

  • Line 1: Trigger Check the event is triggered by the consist leaving the location with the navigation points.
    • Line 2: Navigation Set Check the identified navigation set is checked to see if all its points have been completed. If not then the following lines will be executed simultaneously:-
      • Line 3: Navigation Set Clear the navigation set is cleared so all of its navigation points will be cleared (completed).
      • Line 4: Message Popup Rule a suitable message is displayed on the screen.

Application 3: Wait for Loading to be Completed

The Scenario

A user controlled train arrives at a Navigation Point positioned at a coal loader. Coal loading proceeds. The Navigation Point remains in place until the last wagon is loaded.

Preconditions

  • Navigation Display Rule creates the navigation point set. The Navigation Point is created with its Style set to manual which means it will be completed by another rule and not the arrival of the consist.
NavManualSet.JPG

The Multiple Resouce Check Rule is configured to watch the load of coal in the last wagon of the consist exceeding a set value that is close to the maximum for that wagon (apologies for the colour scheme).

MultResCheck.JPG

Rules Used

The more obvious Wait on Navigation Point Rule is not used because the Navigation Point will be completed manually some time after the consist has arrived at the location. By using the Trigger Check Rule instead (the Navigation Point is attached to a trigger), the navigation icon remains on the screen until the loading has been completed and then it will be manually cleared.

Session Rules Screenshot

NavPointComplete.JPG

Example Explanation

  • Line 1: Trigger Check the event is triggered by the arrival of the consist at the coal loader (the Navigation Point).
    • Line 2: Multiple Resource Check when the last wagon has been loaded the following lines are executed simultaneously:-
      • Line 3: Navigation Point Complete the Navigation Point is completed and its icon is removed from the screen.
      • Line 4: Message Popup a "Loading completed" message appears on the screen.

Application 4: User Path Selection

The Scenario

A user controlled train stops at a navigation point in front of a junction and the driver is offered a choice of paths to allow a passing movement by an AI controlled train. Each path is indicated by different sets of navigation points. The path selected will determine other operations such as junction settings and AI train commands.

Rules Used

Session Logic

NavSidingMap.JPG

Three sets of navigation points are created, one for each location on the map diagram above.

  • Set A: at the junction, Point A in the map diagram. The two signals are set to STOP, Switch 2 is locked in position and the user is presented with a choice of using the Main Line or the Loop Line
  • Set B: at the end signal on the Main Line. Switch 2 is set to the Loop Line and the AI train is given its instructions to pass on the Loop.
  • Set C: at the end signal on the Loop Line. Switch 2 is set to the Main Line and the AI train is given its instructions to pass on the Main.

Session Rules Screenshots and Explanations

Creating the Navigation Point Sets

NavDisplaySets.JPG
  • Each set is created separately and sets B and C are hidden.
  • Each navigation point is attached to a track trigger - Point 1 in Set A is attached to a trigger placed in front of Switch 1 in the map diagram.
NavPointSet.JPG
Navigation Point Set A. Sets B and C are similar.

At Navigation Set A Point 1 The Junction

NavSetsChoose.JPG

Explanation

  • Line 1: Wait on Navigation Point The event is triggered when the consist reaches (and stops at) Navigation Point 1 in Set A.
    • Line 2: Navigation Set Hide/Show The Navigation Set B is made visible.
    • Line 3: Navigation Set Hide/Show The Navigation Set C is made visible.
    • Line 4: Set Junctions The junction Switch 2 is locked against user and AI control.
    • Line 5: Set Signals Extended Signal A is set to STOP
    • Line 6: Set Signals Extended Signal B is set to STOP
    • Line 7: Message Popup A message browser window is shown giving instruction to the user to set Switch 1 to the Loop Line or the Main Line and then move the consist forward to the next signal.

At Navigation Set B Point 1 The Stop signal on the Main Line

NavMainSet.JPG

Explanation

  • Line 1: Wait on Navigation Point The event is triggered when the consist reaches (and stops at) Navigation Point 1 in Set B.
    • Line 2: Navigation Set Clear The Navigation Set C is deleted and its visible Navigation Point disappears from the screen as the Loop Line path was not selected.
    • Line 3: Message Popup A message browser window is shown giving instruction to the user to wait until the passing train has cleared Switch 1
    • Line 4: Set Junctions The junction Switch 2 is set to the Loop Line but is still locked against user and AI control.
    • Line 5: Wait A wait of 20 seconds then ...
      • Line 6: Driver Schedule The AI train is given commands to move to the next destination via the Loop Line.

At Navigation Set C Point 1 The Stop Signal on the Loop Line

NavLoopSet.JPG

Explanation

  • Line 1: Wait on Navigation Point The event is triggered when the consist reaches (and stops at) Navigation Point 1 in Set C.
    • Line 2: Navigation Set Clear The Navigation Set C is deleted and its visible Navigation Point disappears from the screen as the Main Line path was not selected.
    • Line 3: Message Popup A message browser window is shown giving instruction to the user to wait until the passing train has cleared Switch 1
    • Line 4: Set Junctions The junction Switch 2 is set to the Main Line but is still locked against user and AI control.
    • Line 5: Wait A wait of 20 seconds then ...
      • Line 6: Driver Schedule The AI train is given commands to move to the next destination via the Main Line.


Trainz Wiki

Route Creation Tutorials:

Session Creation Tutorials:

Personal tools