SAR Scenario Gladstone-Terowie Passenger

From TrainzOnline
Revision as of 15:11, 12 October 2022 by Pware (Talk | contribs)

Jump to: navigation, search
ArrowLeftBtn.png   4   Gladstone to Jamestown School Run 
 Gladstone to Terowie Passenger 
ArrowRightBtn.png
A scenario in the SAR Peterborough Base Session
A morning school and passenger service from Gladstone to Terowie on Mondays to Fridays and terminating at Jamestown on Saturdays. Bottom

 The Historical Bit 

School runs, services provided to get students to and from their schools, were a regular occurrence in the division. School buses either did not exist or the roads were in such poor condition that bus travel was not practical. In an era where gender segregated schools or classes were much more common than they are today, separate carriages were provided for the boys and for the girls and sometimes even segregated trains were run. It was not always possible to co-ordinate the train services with the school hours so some students would have to leave school at midday to catch the only available service back home that day.


School Run
 Era:  1920s to 1960s
 Duration:  Jamestown: 37 minutes
Terowie: 1 hour 40 minutes
 Loco:  SAR T 200 at Gladstone Station Siding

The Loco Roster Label.png has locos available at the  Peterborough Loco Depot  for an optional loco swap

 Consist:  Attached to SAR T 200
Location Index Each location in the layout has a detailed set of track diagrams that provide a variety of useful information

The  Getting Started  guide below gives a summary of what is available.

To display this information click any Location Index graphic, or go to the bottom of the page for all the session links (all links will open in this window).
Getting Started:
  1. If you have already closed the opening message window then the first step is to pause the session by pressing the  P  key.
  2. Next locate your loco. Either:-
    • Open the Finder Tool (press  Ctrl   F ) and type, in the Name field, the name of the loco, in this case SAR T 200 (or just T 200 should be enough). Click the tick icon, OR
    • Open the Driver List (bottom left of the screen) and then scroll through the list to find the loco name (SAR T 200) then click the drivers Eye icon Driver Eye.png to take control of the loco
    • Open the Driver List (bottom left of the screen) and then scroll through the list to find either:-
    • the loco name (SAR T 200) OR
    • the driver icon (named Driver 200) - this is a non-animated icon
    then click the drivers Eye icon Driver Eye.png to take control of the loco
  3. Take a few moments to get your bearings. Click Gladstone Data (this link will open in this window) to show the location details and track plans for Gladstone. In each location details page:-
    • the Tab HM White.png tab gives an overall summary of each location with a "potted" history (where available).
    • the Tab TM Grey.png tab reveals the invisible TM Track Marks for Drive To commands.
    • the Tab IN Grey.png tab lists all active industries and their commodities.
    • the Tab SW Grey.png tab describes the names, locations and settings of all junction switches as well as some switch sets you may want to use.
  4. Each location details page has direct links to the adjacent locations so you can explore along the route.
  5. When you are ready to start, reload the Peterborough Base Session page (click the Scenarios button on your current location page) and select this Scenario again or just use the Back button on your browser - whichever is quicker.
  6. Switch back to Driver Mode and either close the opening message window or press the  P  key to start the session.


Tutorial:
Tutorial A tutorial on using these scenarios is provided in the link on the left. The link will open in this window


Orders:
  1. Reverse the train into Gladstone  Station  from the storage siding
  2. Proceed according to the working timetable shown below
  3. When terminating at Jamestown stable the cars on one of the  Loco Sidings 
  4. When terminating at Terowie stable the cars on one of the  Station Sidings  and service the loco at the  Loco Depot 
Logo
 Gladstone-Terowie Morning Local Passenger 
37
  Frequency
Train №
Mon to Fri
GP5
Sat
GP7
 
Gladstone Car Siding dep 08:00 08:00  
Station dep 08:05 08:05  
Yangya arr a a a - on request stop
Caltowie arr 08:26 08:26  
Jamestown arr 08:37
W
08:37
CWTS
Coal and Water loco if required, Turn loco, Stable cars and loco
Belalie North arr 08:50    
Yongala arr 09:03    
Peterborough West arr a   a - on request stop
Peterborough arr 09:14
W
 
Water loco
dep 09:20    
Terowie arr 09:50
CWTS
  Coal and Water loco if required, Turn loco, Stable cars and loco


Driving Notes:

A summary of the facilities and product loads at all locations along the lines is provided in the links

Port Pirie-Broken Hill Line and Peterborough-Terowie Line
  • The approaches to all locations are protected by invisible signals to prevent the AI Half Speed Slowdown Problem when approaching a signal at stop.
  • Trackmarks and industries have been provided for AI Drive To Trackmark, Drive via Trackmark and Drive to  Industry  commands. Click Location Index for details.
  • Industry active stations (where you can use the Drive To industry command) are only at Gladstone, Jamestown, Peterborough and Terowie. Industry active stations will have a longer than expected wait time.
  • Manual (no AI) driving is possible. As a visual driving aid, a Caution warning sign has been placed at the location of the Main Approach Dn and Main Approach Up trackmarks. Click Location Index for details.
  • If driving manually in yards, you are responsible for correctly setting any catch points.
Strip Map
Route Key

Links: All links will open in this window
ArrowLeftBtn.png Scenarios
Session Scenarios
Location Index
Location List
Tutorial
Drive Tutorial
Rolling Stock
Rolling Stock
Loco Roster
Loco Roster
Industries
Active Industries
Top ArrowRightBtn.png


This page was created by Trainz user pware in February 2021 and was last updated as shown below.



Personal tools