Gladstone to Jamestown School Run
Gladstone to Terowie Passenger |
| A scenario in the SAR Peterborough Base Session |
A morning school run from Gladstone to Jamestown on Mondays, Wednesdays, Fridays.
Combined school run and morning passenger service from Gladstone to Terowie on Tuesdays, Thursdays, Saturdays. |
 |
 |
| Duration: |
Jamestown School Run 35 minutes
Terowie Passenger 1 hour 40 minutes |
| Loco: |
SAR T 200 at Gladstone Station Siding
Other Unrostered Locos:
- SAR T 210 at Gladstone Depot
- SAR T 23 on Peterborough Depot Siding 1
- SAR T 233 on Peterborough Depot Loco Road 1
- SAR 407 on Peterborough Depot Repair Shop Road 4
|
| Consist: |
Attached to SAR T 200. 2 Kuranda BL1 coaches, 1 DB Guard Van |
|
 |
Each location in the layout has a detailed set of track diagrams that provide a variety of information. The Getting Started guide below gives a summary of the information that is available.
To display the data click any Line Index graphic, or go to the bottom of the page for all the session links (all links will open in this window). |
|
|
Getting Started:
- The first step is to pause the session by pressing the P key.
- Next locate your loco. Either:-
- Open the Finder Tool (press CTRL-F) and type, in the name field, the name of the loco. For example SAR T 200 (or just T 200 should be enough). Click the tick icon, OR
- Open the Driver List (bottom left of the screen) and select the loco from there - click the drivers Eye icon to jump to the loco.
- Take a few moments to get your bearings. Use the (this link will open in this window) and click on Gladstone to load its location details and track plans. In each location details page:-
- the
 tab will identify the EIT Paths that are available if you wish to use them.
- the
 tab will reveal the invisible  Track Marks for Drive To commands.
- the
 tab will show all active industries and their commodities.
- the
 tab will give you the names, locations and settings of all junction switches as well as some switch sets you may want to use.
- Each location page has direct links to the next locations so you can explore along the route.
- When you are ready to start, reload the Peterborough Base Session page (click the Scenarios button on your current location page) and select this Scenario again or just use the Back button on your browser - whichever is quicker.
- Switch back to TRS19 Driver and press the P key to start the session.
|
|
Tasks:
- Reverse the train into Gladstone Station .
- On Mondays, Wednesdays, Fridays proceed to the Stations at Caltowie and Jamestown. Terminate at Jamestown.
- On Tuesdays, Thursdays, Saturdays proceed to the Stations at Yangya (request stop), Caltowie, Jamestown, Belalie North, Yongala, Peterborough and Terowie. Terminate at Terowie.
- Coal (if needed) and water at the destination.
|
 |
Driving Notes:
- The approaches to all locations are protected by invisible signals to prevent the AI Half Speed Slowdown Problem when approaching a signal at stop.
- Enhanced Interlocking Towers with set paths are available for your optional use at Gladstone (departure), Jamestown (arrival and departure), Peterborough (arrival and departure) and at Terowie (arrival). Click for details.
- Trackmarks and industries have been provided for AI Drive To Trackmark, Drive via Trackmark and Drive to Industry commands. Click for details.
- Manual (no AI) driving is possible. For those locations without home or approach semaphore signals, a Caution warning sign has been placed at the location of the Main Approach Dn and Main Approach Up trackmarks. Click for details.
|
|
|
This page was created by Trainz user pware in February 2021 and was last updated as shown below.
