Revision as of 14:00, 30 June 2021

The information in this Wiki Page applies to TRS19 Platinum Edition and Trainz Plus. Older versions of Trainz, including T:ANE and TRS19 (standard), do not have the UDS feature described in this document.

What is the UDS Interface?

	The UDS provides a means of quickly switching from Driver mode to Surveyor mode and back to Driver again without having to restart a running session after each switch. It is only available in TRS19 Platinum Edition and Trainz Plus
	The UDS replaces the QuickDrive Rule in TRS19 Platinum Edition and Trainz Plus

UDS stands for Universal Driver Surveyor and is an "interface' or option built into TRS19 Platinum Edition and Trainz Plus that allows you to jump seamlessly from Driver into Surveyor and then back into Driver again to resume a session at the point where you left it. There is no need to restart a Driver session from the very beginning.

Previously (before UDS) your only options would be to:- ignore the problem (if possible) to continue the session in Driver and fix the problem later, or immediately halt the session to fix it now In both cases you would have to:- load the route into Surveyor and try to recall exactly where the problem is located fix the problem restart the session in Driver from the beginning (a bit tough if you were 2 hrs or more into a 3 hr session)

The UDS interface allows you to halt the Driver session (press the  P  key) and then switch, via a menu option, to Surveyor without having to stop and exit Driver mode first.

		All the Surveyor tools and options are available for you to use, including the Session Editor (more on that later).
		You use the Surveyor tools to fix the problem, such as deleting (as shown left), moving or adding a scenery object. You can then (if you wish) save the edited route and/or session (again there will be more on that later).
		You then switch back into Driver to continue driving the session with the problem fixed.

Switching Modes

	When in Driver Mode Switching to Surveyor
		Open the Tools Menu and select Surveyor Mode Warning: Trains that are moving in Driver mode when you switch to Surveyor Mode will continue to move in Surveyor. This can lead to derailments or other problems. It is recommended that you select the Pause option (at the top of the Tools menu) or hit the  P  key before switching to Surveyor
	When in Surveyor Mode Switching to Driver
		Open the Tools Menu and select Driver Mode If you had paused Driver before switching to Surveyor then the simulation will be paused and the Paused message will appear on the screen. Hit the  P  key to resume.

Saving

Warning:
	If you decide to save your Surveyor edits and select the option to then you will "overwrite" (a nicer way of saying destroy) your starting or original session

Most of the problems users seem to be experiencing with the UDS, judging from the posts in the Trainz Forums, is when saving their edited Driver session after switching to Surveyor mode.

	Using Driver Mode involves driving consists (either manually or through the AI) and activating rules. These will change the session parameters
	Overwriting the Session will save the consist locations and Session Rules in their new positions/conditions

Notes: An important change that has been introduced by the UDS is that train vehicle placement is now saved as part of the Session, even if those vehicles have been placed in Route Layers.

In TRS19 Platinum Edition and in Trainz Plus it is recommended that all consists should be placed into a Session Layer and become part of a Session instead of the Route

When you are in Driver Mode at least one of the consists will probably be moving. Some of the Session rules may have already been completed while others may still be running or waiting for events (e.g. triggers to be activated).

If you then choose to save using the Overwrite existing session option then you will be replacing your original starting Session with a new one with the consists saved in their new positions and the Session rules saved in their new states. So when you later load and restart the Session things will not be the same.

Unless you have a particular reason for overwriting the Session, then the recommended save options are:-

	Do not save session This will only save the Route using its existing name. Since most or all scenery and track objects should be in the Route Layers and not the Session Layers, this will save any scenery edits that you have made.
	Create new session This will save the Route using its existing name. It will also save the Session using a new name you enter in the text box below the option (Stage 3 in the example shown). The original Session will not be altered. This is useful when you want to test out changes to consists, industry settings, Rules, driver commands, etc but do not want to destroy the original Session.

Resetting the Session Rules

After you switch from Driver Mode to Surveyor Mode it may be necessary to restart or reset some of the Session Rules

As mentioned above, when Driver Mode is running some of the Session rules may be completed while others may still be running or waiting for certain events (e.g. triggers to be activated). When you switch to Surveyor Mode these rules may be in a different state compared to what they were at the start of the Session. When you restart Driver Mode these rules may not be in a useful condition.

The Session Editor built into all Trainz versions allows you to add, delete and modify the rules that will operate during a Session. More information on the Session Editor can be found on the Trainz Wiki at Using the Session Editor

To open the Session Editor open the Edit menu and select Edit Session

	At the bottom of the Session Editor is a new button, Reset All Rules. This will reset or restart ALL rules in the Session.
	Some rules, as shown in the screen shot above, have the label (Complete was-complete) after the rule name. This indicates that the rule has already been completed. These rules can be individually restarted by right mouse clicking on the rule and selecting the Reset option from the pop up menu. This will change the rule status to (Paused).
When the Driver Mode is selected again, all the reset or Paused rules will be restarted.

Some Questions Answered

I have only edited assets that are in the Route layers but selecting Save always sets the option to "Overwrite exiting session" as the default. Why?

Many scenery assets actually have their properties stored in the Session, even when the assets themselves are in a Route layer. Editing the properties of these assets is considered to ne a change to the Session. These include:-

• junction switches - the left/right switch direction is stored in the Session
• industries - the commodities and quantities loaded/unloaded are stored in the Session
• wagon commodities and quantities carried
• consist locations (TRS19 Platinum Edition and Trainz Plus only)
• named scenery objects - the name is stored in the Session

Interlocking Towers (including Enhansed Interlocking Towers) show paths as "not editable" after switching to Surveyor Mode. Why?

If you make the switch from Driver Mode to Surveyor Mode after a IT/EIT path has been activated (but not yet cleared or cancelled) then you will be unable to edit that path. In addition, you will not be able to add new paths to a IT/EIT that has an open active path.

pguy, the creator of the EIT asset and associated rules, has a detailed description of this and some possible solutions in a Trainz Forum post at:- EITs and the UDS

Trainz Wiki

More Tutorials and Guides to Using Trainz How to Guides Driver Commands List Session Rules List (Alphabetical) with Parameters Session Rules List (Categories) With Parameters

This page was created by Trainz user pware in June 2021 and was last updated as shown below.