From TrainzOnline
(Difference between revisions)
|
|
| Line 102: |
Line 102: |
| | <tr valign="top"> | | <tr valign="top"> |
| | <td> | | <td> |
| | + | *The '''Wilmington Line''' is '''not signalled'''. Normally only one train is allowed on the line at any one time. |
| | + | *You have been issued with an authority ticket for the '''Wilmington Line''' which is valid to the '''Army Siding Junction'''. |
| | *You have permission to pass semaphore signals at stop provided you are satisfied that the road ahead is clear. | | *You have permission to pass semaphore signals at stop provided you are satisfied that the road ahead is clear. |
| − | *You have been issued with the line access ticket for the '''Wilmington Line''' as far as the '''Army Stores Siding Junction'''.
| |
| | </td> | | </td> |
| | </tr> | | </tr> |
Revision as of 20:10, 28 February 2021
Getting Started:
- The first step is to pause the session by pressing the P key.
- Next locate your loco. Either:-
- Open the Finder Tool (press CTRL-F) and type, in the name field, the name of the loco. For example SAR T 210 (or just T 210 should be enough). Click the tick icon, OR
- Open the Driver List (bottom left of the screen) and select the loco from there - click the drivers Eye icon to jump to the loco.
- Take a few moments to get your bearings. Use the
 (this link will open in this window) and click on Gladstone to load its location details and track plans. In each location details page:-
- the
 tab will identify the EIT Paths that are available if you wish to use them.
- the
 tab will reveal the invisible  Track Marks for Drive To commands.
- the
 tab will show all active industries and their commodities.
- the
 tab will give you the names, locations and settings of all junction switches as well as some switch sets you may want to use.
- Each location page has direct links to the next locations so you can explore along the route.
- When you are ready to start, reload the Peterborough Base Session page (click the Scenarios button on your current location page) and select this Scenario again or just use the Back button on your browser - whichever is quicker.
- Switch back to TRS19 Driver and press the P key to start the session.
|
|
Yard Map: |
 |
 |
Tasks:
- Move the loco out of the Loco Depot and run tender first onto the Wilmington Line to the Gladstone Army Stores Junction about 1/3rd of a mile up the line.
- Set the mechanical indicator lever and move onto the Army Stores Siding.
- Attach to the empty wagons at the narrow gauge loading dock platform.
- Move the wagons onto the Wilmington Line resetting the mechanical indicator lever at the junction as you go.
- Move the loco and wagons to the Goods Shed to load the QLX wagons.
- After loading uncouple the loco and MTW wagons from the CCC and QLX wagons and move the MTW wagons progressively through the Goods Crane to load.
- Shunt the MTW wagons back to couple with the CCC and QLX wagons. Detach the loco.
- Return the loco to the Loco Depot and attach to the empty CCC and Tanker wagons stored at the end of the Fuel road.
- Move the wagons out of the Loco Depot and couple them to the wagons waiting in the Goods Shed .
- Return the loco to its starting position in the Loco Depot.
|
Driving Notes:
- The Wilmington Line is not signalled. Normally only one train is allowed on the line at any one time.
- You have been issued with an authority ticket for the Wilmington Line which is valid to the Army Siding Junction.
- You have permission to pass semaphore signals at stop provided you are satisfied that the road ahead is clear.
|
|
|
This page was created by Trainz user pware in February 2021 and was last updated as shown below.
