HowTo/Use Superelevation with Trainz 22

From TrainzOnline
< HowTo
Revision as of 12:50, 4 October 2024 by Vincentrh (Talk | contribs)

(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search



Contents

What is superelevation in Trainz 22?

The "superelevation" or the slope of rails in curves is proposed since T:ANE. This page updates the instructions for Trainz 22


To resist centrifugal force and and not to wear out prematurely the outer rail, the track must be tilted on bends.
Applying a gradient to a curved section of track is called superelevation.

Here is the example of a machine launched to 80 kph in a curve of 500 meters of beam. The slope of the track has been set to 4 °.
5.jpg



To implement Superelevation in Trainz 22, follow the steps below :


On the tools palette,select the highlighted icone as shown on the opposite picture (1)

Clic on the track to select it (2)

Clic on one of the submits of the selected track (3)
SE1.jpg


Clic on Edit Properties (1)

Complete both sections (2)
Determining the variable 'Superelevation Degree' is essential for applying superelevation to a curve...
more details to follow in this ‘How To’...

Do the same with the other submit of the track
SE2.jpg



Surperelevation : theoritical base

  Everything that follows in this section is designed to give you the theoretical basis for calculating a superelevation. In the next section, a spreadsheet will be provided to do all the calculations for you.

  •   The Superelevation (SE) is the height that the outside rail takes compared with the internal rail in a curve.

        It is calculated as the diagram below shows it:

Img396bis.jpg

1 - Maximum value of SE is limited to 16 cm (6.3 inches) for standard gauge tracks and 10 cm (3.14 inches) for metric tracks.
2 - Superelevation Limit (or degree of slope A deg) is limited to 6.4° for standard gauges and 5.8° for metric gauges.
3 - There is no superelevation for speeds lower than 25 kmh (15.5 mph) in standard gauge and 30 kmh (18.5 mph) in metrics.
4 - On networks with gauge of 60 cm (2 ft) or less, the speed is limited to 25 kmh (15.5 mph) : there is thus no superelevation either.




  •   Of the four variables above (G, V, R,g), one is unknown at start: the radius of the curve.

        The diagram below shows how to determine it :
   Img397bis.jpg

  •   Trainz 22 introduces an aditionnal concept for determining the superelevation of a curve: the degree of curvature.
Here, with a quarter-circle curve, the curve angle is 90°.

The more open the curve, the greater the angle.

The tighter the curve, the smaller the angle.
Img402.jpg


To apply superelevation in Trainz, we saw above that we had to calculate the 'superelevation degree'. More precisely, this means to determine the angle of the slope by degree of the concerned curvature.
Example: we have a curve with a curve angle of 60° and a superelevation angle of 4°. The 'superelevation degree" will be equal to 4/60 = 0.066.



Superelevation: how do we go about it?


To proceed to the calculations, download and save to your hard drive the spreadsheet Here


Proceed in two steps :

  • measure the chord and arrow of your curve
  • proceed to the calculations with the spreadsheet

Measure the chord and arrow of your curve :

In your Asset Pallet, select the spline 'ruler' <kuid:447125:108> Ruler Metric or <kuid:447125:109> Ruler Imperial

Measure the lengths of the chord and the arrow as shown opposite

Img399.jpg



Procced to the calculations whith the spreadsheet :


  • Enter the values of chord and arrow (1)
  • Indicate the maximum speed in the bend and choose between 'standard' or 'metric' gauge (2)
  • Look at the value of SuperElevation now displayed (3) : it doesn't have to exceed 16 cms (6.3 inches) in standard gauge tracks and 10 cms (3.94 inches) in metrics -French standard-. If these values are exceeded, reduce the Max speed.
  • Note the value of superelevation degree (4) and complete the property 'Superelevation Degree' of your track as shown in the first section.
  • Also complete the second property 'Superelevation Limit' with these values : 6,4 (standard gauge) or 5,8 (metric gauge).
Img401bis.jpg



Discussion on the effectiveness of elevation with Trainz 22

Now we are expert on Superelevation, how does it work in Trainz 22?

Let's see with a simple exemple : with a curve (chord = 145m, arrow = 24, max speed = 30 kmh, metric gauge), our spreadsheet calculates a track inclination = 3.3° for a Angle of curve = 73.3 and a Superlevation Degree = 0.05 :

1 - We do same calculations with the old version of the spreadsheet for an aplication with Trainz 2019 (see How/To HowTo/Use Superelevation )
2 - For Trainz 22 environment, we set the Superelevation Degree to 0.05 (according the results of the spreadsheet) and also at its maximum (1 by degree of Angle of bank).

And here is the result :

Img404.jpg

I must say that the elevation function works very well with trainz 2019. This is no longer the case with trainz 22.
Well, all I have to do is send a bug report.
Personal tools