CCG/Modelling: 3DSMax Initial Setup

From TrainzOnline
< CCG(Difference between revisions)
Jump to: navigation, search
(New page: 3DSMax/gmax Initial Setup You should first set up 3dsmax or gmax with default settings, both programs have similar settings. The units are easiest to work with when set to metric, some exp...)
 
Line 1: Line 1:
3DSMax/gmax Initial Setup
+
==3DSMax Initial Setup==
You should first set up 3dsmax or gmax with default settings, both programs have similar settings. The units are easiest to work with when set to metric, some experience problems with animation in imperial units.
+
  
Set the menus as follows:
+
===GMax Note:===
 +
'''GMax''' is no longer supported by N3V Games (Auran).  The exporter package in '''Trainz Asset Creation Studio''' does not produce the latest mesh versions that support normal mapping or graphics processor based animations. So only references to 3DSMax will be included here.
  
1. From the Customise .. Preference Settings .. General, set the System Units Scale
+
Also please do not upload animated meshes from GMax to the Trainz DownLoad Station. The old type of animations put unnecessary load on to the CPU which is better directed to other parts of the game.
  
2. From the Customise .. Units Setup, set the Units
+
===Setting Up 3DSMax===
 +
 
 +
You should first set up 3DSMax with default settings. The units are easiest to work with when set to metric; some experience problems with animations in imperial units.
  
3. From the Grid and Snap Settings ..Home Grid, set the grid to a very fine value, say 0.01 metres. This allows you to have a fine grid when you zoom in, and allows you to snap objects to the grid points (this option may be turned on or off in 3dsmax/gmax). The grid will not clutter the screen as it only shows a grid density suitable for viewing as you zoom in or out.
+
Set the '''menus''' as follows:
  
4. From the Customise .. Preferences .. Files, some boxes may already be ticked, but the following settings are useful:
+
'''1.''' From the Customise .. Preference Settings .. General, set the System Units Scale
  
Increment on save, after first saving the file with a name of your choice, subsequently using the save button will automatically create a new saved file, incrementing the file number. For a file called bridge, this gives bridge001, bridge002 etc as you Save the file, you do not need to use Save As. Save often, and if you have a problem with the model you can go back a few saved steps and start again. When you have finished the model, you can remove unnecessary older saved files.
+
'''2.''' From the Customise .. Units Setup, set the Units
  
It is very important to check the Auto Backup. If 3dsmax or gmax crashes (and it sometimes does, when you are trying to undo too many steps when mapping, or typing a material name in some of the dialogue boxes in gmax) you can find three files called Autobak001, 002, 003 in the Autobak directory.
+
'''3.''' From the Grid and Snap Settings ..Home Grid, set the grid to a very fine value, say 0.01 metres. This allows you to have a fine grid when you zoom in, and allows you to snap objects to the grid points (this option may be turned on or off in 3dsmax/gmax). The grid will not clutter the screen as it only shows a grid density suitable for viewing as you zoom in or out.
  
3dsmax cycles through these numbers and overwrites them. Find the directory, look at the time stamp for the most recent file, open it in 3dsmax or gmax and you will only have lost up to 5 minutes of work (whatever time you have set). You may have to "Show All Files" to see the file, when trying to open it from the Autobak directory.
+
'''4.''' From the Customise .. Preferences .. Files, some boxes may already be ticked, but the following settings are useful:
  
5. From the Customise .. Configure Paths .. General you can choose the paths for your files. It is useful to set the Export path to the full directory of the Custom Trainz  directory in TRS2004 or the editing directory in TC. It is  simple to then navigate to the particular model directory  from there, without navigating from the C: directory every  time you export a file.
+
''Increment on save'', after first saving the file with a name of your choice, subsequently using the save button will automatically create a new saved file, incrementing the file number. For a file called bridge, this gives bridge001, bridge002 etc as you Save the file, you do not need to use Save As. Save often, and if you have a problem with the model you can go back a few saved steps and start again. When you have finished the model, you can remove unnecessary older saved files.
  
An easy way to have consistent 3dsmax/gmax settings  is to load a previous model and then select the "new file"  option to begin a new model, retaining the settings from  the previous loaded file.
+
It is very important to check the ''Auto Backup''. If 3DSMax crashes (and it sometimes does, when you are trying to undo too many steps when mapping, or typing a material name in some of the dialogue boxes) you can find three files called Autobak001, 002, 003 in the ''Autobak'' directory.
  
One issue with 3dsmax4/gmax is "saved file corruption",  caused by a Microsoft upgrade. Your saved files naturally get larger as you work, but a reasonable files size may be 100k to 400k, depending on the model. Sometimes the next file save becomes corrupted and the file size will jump to 2 or 3mb.   While it does not seem to have any effect on the file contents, you will notice this effect by the greatly  increased save and load time of the file. Do not merge  any object from the corrupted file into a new file, it can  corrupt the new file as well, and inflate the size. If you
+
3DSMax cycles through these numbers and overwrites them. Find the directory, look at the time stamp for the most recent file, open it in 3DSMax and you will only have lost up to 5 minutes of work (whatever time you have set). You may have to "Show All Files" to see the file, when trying to open it from the Autobak directory.
were also using the Increment on Save option, you can  then end up with many large files, using up valuable disk  space.
+
  
This had been recognised by Discreet, and information is  available on the Discreet site:
+
'''5.''' From the Customise .. Configure Paths .. General you can choose the paths for your files. It is useful to set the Export path to the editing directory in your version of Trainz. It is  simple to then navigate to the particular model directory from there, without navigating from the C: directory every time you export a file.
  http://usa.autodesk.com/adsk/servlet/ps/item?siteID=123112&id=5582099&linkID=5573345
+
 
 +
An easy way to have consistent 3DSMmax settings is to load a previous model and then select the "new file"  option to begin a new model, retaining the settings from  the previous loaded file.
 +
 
 +
One issue with 3DSMax4 is "saved file corruption", caused by a Microsoft upgrade. Your saved files naturally get larger as you work, but a reasonable files size may be 100k to 400k, depending on the model. Sometimes the next file save becomes corrupted and the file size will jump to 2 or 3mb.  While it does not seem to have any effect on the file contents, you will notice this effect by the greatly  increased save and load time of the file. Do not merge  any object from the corrupted file into a new file, it can  corrupt the new file as well, and inflate the size. If you were also using the Increment on Save option, you can  then end up with many large files, using up valuable disk  space.
 +
 
 +
 
 +
 
 +
==Return to CCG Index==
 +
[[Content Creator's Guide]]
 +
 
 +
[[CCG/Kind_Examples|Kind Examples]]

Revision as of 21:28, 13 June 2011

Contents

3DSMax Initial Setup

GMax Note:

GMax is no longer supported by N3V Games (Auran). The exporter package in Trainz Asset Creation Studio does not produce the latest mesh versions that support normal mapping or graphics processor based animations. So only references to 3DSMax will be included here.

Also please do not upload animated meshes from GMax to the Trainz DownLoad Station. The old type of animations put unnecessary load on to the CPU which is better directed to other parts of the game.

Setting Up 3DSMax

You should first set up 3DSMax with default settings. The units are easiest to work with when set to metric; some experience problems with animations in imperial units.

Set the menus as follows:

1. From the Customise .. Preference Settings .. General, set the System Units Scale

2. From the Customise .. Units Setup, set the Units

3. From the Grid and Snap Settings ..Home Grid, set the grid to a very fine value, say 0.01 metres. This allows you to have a fine grid when you zoom in, and allows you to snap objects to the grid points (this option may be turned on or off in 3dsmax/gmax). The grid will not clutter the screen as it only shows a grid density suitable for viewing as you zoom in or out.

4. From the Customise .. Preferences .. Files, some boxes may already be ticked, but the following settings are useful:

Increment on save, after first saving the file with a name of your choice, subsequently using the save button will automatically create a new saved file, incrementing the file number. For a file called bridge, this gives bridge001, bridge002 etc as you Save the file, you do not need to use Save As. Save often, and if you have a problem with the model you can go back a few saved steps and start again. When you have finished the model, you can remove unnecessary older saved files.

It is very important to check the Auto Backup. If 3DSMax crashes (and it sometimes does, when you are trying to undo too many steps when mapping, or typing a material name in some of the dialogue boxes) you can find three files called Autobak001, 002, 003 in the Autobak directory.

3DSMax cycles through these numbers and overwrites them. Find the directory, look at the time stamp for the most recent file, open it in 3DSMax and you will only have lost up to 5 minutes of work (whatever time you have set). You may have to "Show All Files" to see the file, when trying to open it from the Autobak directory.

5. From the Customise .. Configure Paths .. General you can choose the paths for your files. It is useful to set the Export path to the editing directory in your version of Trainz. It is simple to then navigate to the particular model directory from there, without navigating from the C: directory every time you export a file.

An easy way to have consistent 3DSMmax settings is to load a previous model and then select the "new file" option to begin a new model, retaining the settings from the previous loaded file.

One issue with 3DSMax4 is "saved file corruption", caused by a Microsoft upgrade. Your saved files naturally get larger as you work, but a reasonable files size may be 100k to 400k, depending on the model. Sometimes the next file save becomes corrupted and the file size will jump to 2 or 3mb. While it does not seem to have any effect on the file contents, you will notice this effect by the greatly increased save and load time of the file. Do not merge any object from the corrupted file into a new file, it can corrupt the new file as well, and inflate the size. If you were also using the Increment on Save option, you can then end up with many large files, using up valuable disk space.


Return to CCG Index

Content Creator's Guide

Kind Examples

Personal tools