SAR Scenario Gladstone Bulk Ore V1

From TrainzOnline
Jump to: navigation, search
ArrowLeftBtn.png
 4 
  5   Paratoo to Gladstone Bulk Ore 

A scenario in the SAR Peterborough Base Session v1.0

For the updated V2.0 scenario, click here
ArrowRightBtn.png
  6 
Express bulk ore freight from Broken Hill to Port Pirie with a refuelling stop and an optional loco swap at Peterborough. Bottom

 The Historical Bit 

The line from Port Pirie to Cockburn on the South Australia - New South Wales border was built in stages from 1875 to 1888 largely to capture the lead, zinc and silver ore traffic from the mines at Broken Hill just over the border in New South Wales. Because the SAR was not allowed to operate into New South Wales, a private railway, the Silverton Tramway, was created to carry the ore across the border. The SAR and Silverton Tramway simply swapped locos at Cockburn on the border. It was called a "tramway" to get around a NSW law banning private railways but not private tramways. Despite the title it was a fully operating heavy haul railway, and one of the most profitable in the country.

The SAR had a monopoly on the ore traffic until 1919 when the NSWGR (New South Wales Government Railways) completed its own standard gauge (4ft 8½in) line from Sydney to Broken Hill but the SAR continued to carry the bulk of the ore because the port and smelter at Port Pirie was much closer to Broken Hill.

A variety of motive power was used on the ore trains. SAR Y class locos were originally used then the SAR T class took over until they were largely replaced by the SAR 406 class locos in the 1950s. In the 1960s the SAR 830 class (narrow gauge) diesel locos started appearing.

By 1970 the narrow gauge line from Port Pirie to Broken Hill had been converted to standard gauge and the Silverton Tramway ceased its ore hauling operations but continues to operate today providing standard gauge shunting services and loco leasing to other rail operators. The SAR 830 class (standard gauge) diesels continued to haul the ore trains well into the 2000s.


Loaded Ore
 Era:  1950s and 1960s
 Duration:  Peterborough: 1 hour 25 minutes (includes refuelling time)
Gladstone: 2 hours 45 minutes
 Loco:  SAR 406 (Garrett) on the  Main  line approaching Paratoo from the East

The Loco Roster Label.png has locos available at the  Peterborough Loco Depot  for an optional loco swap

 Consist:  Attached to SAR 406
Location Index Each location in the layout has a detailed set of track diagrams that provide a variety of useful information

The  Getting Started  guide below gives a summary of what is available.

To display this information click any Location Index graphic, or go to the bottom of the page for all the session links (all links will open in this window).
Getting Started:
  1. If you have already closed the opening message window then the first step is to pause the session by pressing the  P  key.
  2. Next locate your loco. Either:-
    • Open the Finder Tool (press  Ctrl   F ) and type, in the Name field, the name of the loco, in this case SAR 406 (or just 406 should be enough). Click the tick icon, OR
    • Open the Driver List (bottom left of the screen) and then scroll through the list to find the loco name (SAR 406) then click the drivers Eye icon Driver Eye.png to take control of the loco
  3. Take a few moments to get your bearings. Click Paratoo Data (this link will open in this window) to show the location details and track plans for Paratoo. In each location details page:-
    • the Tab HM White.png tab gives an overall summary of each location with a "potted" history (where available).
    • the Tab TM Grey.png tab reveals the invisible TM Track Marks for Drive To commands.
    • the Tab IN Grey.png tab lists all active industries and their commodities.
    • the Tab SW Grey.png tab describes the names, locations and settings of all junction switches as well as some switch sets you may want to use.
  4. Each location details page has direct links to the adjacent locations so you can explore along the route.
  5. When you are ready to start, reload the Peterborough Base Session page (click the Scenarios button on your current location page) and select this Scenario again or just use the Back button on your browser - whichever is quicker.
  6. Switch back to Driver Mode and either close the opening message window or press the  P  key to start the session.


Tutorial:
Tutorial A tutorial on using these scenarios is provided in the link on the left. The link will open in this window


Orders:
  1. Move the train into Paratoo Yard on the  Main  Line
  2. Fill the tender with water at the  Water  Column or proceed to Nackara and fill with water at the  Water  Column located there.
  3. Proceed to Peterborough  Loop  or Peterborough  Yard 1 .
  4. Detach the loco and proceed to Peterborough Main  Loco Fuel & Water  Point to refuel the tender with bunker c oil and water.
  5. Reattach the loco, or another available loco, to the train and proceed by 09:30 to Gladstone  Yard . If you are replacing the 400 class with a different type of loco then you are advised to double-head.
Logo


Driving Notes: tr valign="top"> </tr>

A summary of the facilities and product loads at all locations along the line is provided in the link Port Pirie-Broken Hill Line

  • Fuel oil level is low, but sufficient to reach Peterborough where it can be refilled
  • Water is very low and you will need to refill either here at Paratoo or at Nackara
  • The length of the train restricts its use of passing loops and yard loops to those located at:-
    • Methuen Loop
    • Nackara Station Loop and Nackara Goods
    • Peechara Loop (Note that Nantabibbie Loop is too short)
    • Oodla Wirra Station Loop
    • Ucolta Station Loop
    • Peterborough Loop, Peterborough Station and Peterborough Yard 1
    • Yongala Station Loop and Yongala Goods Loop
    • Belalie North Station Loop
    • Jamestown Station + Yard, Jamestown Loop + Yard and Jamestown Goods Loop + Yard
    • Caltowie Station Loop
    • Gladstone (all loops and yards).
  • The approaches to all locations are protected by invisible signals to prevent the AI Half Speed Slowdown Problem when approaching a signal at stop.
  • Trackmarks and industries have been provided for AI Drive To Trackmark, Drive via Trackmark and Drive to  Industry  commands. Click Location Index for details.
  • Manual (no AI) driving is possible. As a visual driving aid, a Caution warning sign has been placed at the location of the Main Approach Dn and Main Approach Up trackmarks. Click Location Index for details.
  • If driving manually in yards, you are responsible for correctly setting any catch points.
Strip Map
Route Key

Links: All links will open in this window
ArrowLeftBtn.png
  4 
Scenarios
Scenario Index
Location Index
Location Index
Tutorial
Drive Tutorial
Rolling Stock
Rolling Stock List
Loco Roster
Loco Roster
Industries
Active Industries
Top ArrowRightBtn.png
  6 


This page was created by Trainz user pware in February 2021 and was last updated as shown below.


Personal tools