SAR Scenario Terowie Shunter

From TrainzOnline
Revision as of 21:36, 18 February 2021 by Pware (Talk | contribs)

Jump to: navigation, search

 Terowie Shunter 

Shunting operations in Terowie Yard.

Shunter
Scenarios SAR Peterborough Base Session Scenarios List
Each location in the layout has a detailed set of track diagrams that provide the following information:-
Location Index
Line Index
  • the names of the tracks, sidings and loops
  • the location of various facilities - stations, turntables, water columns, coal stages, engine sheds, active industries
  • the names of active industries and their products and consumables
  • the names and locations of trackmarks for Drive To and Drive Via commands
  • the names, properties and locations of track switches and lists of switch sets for particular movements
  • Enhanced Interlocking Tower paths for those locations that have EITs
Click Line Index Label.png or the graphic above to access the location data (link will open in this window).

Other Links: (these will open in this window)
Rolling Stock Locomotives and Rolling Stock - commodities carried
Industries Active Industries - commodities produced and consumed

Duration: xx minutes
Loco: SAR T 198 at Terowie Depot

Other Unrostered Locos:

  • SAR T 231 at Terowie Depot

Getting Started:

  1. The first step in Driver is to locate your loco. Open the Finder (press CTRL-F) and type, in the name field, the name of the loco. For example SAR T 198 (or just T 198 should be enough). Click the tick icon.
  2. Next pause the simulation by pressing the P key.
  3. Take a few moments to get your bearings. Use the Line Index Label.png (this link will open in this window) and click on Terowie to load its location details and track plans. The Tab PH Grey.png tab will give you the EIT Paths that are available if you wish to use them but probably not in this scenario. The Tab TM Grey.png tab will give you the location and names of the invisible Track Marks for Drive To commands. The Tab IN Grey.png tab will show the names and locations of all active industries and their commodities. The Tab SW Grey.png tab will give the names and locations of all junction switches as well as some switch sets you may want to use.
  4. When you are ready to start, reload the Peterborough Base Session page (click the Scenarios button on your current location page) and select this Scenario again or just use the Back button on your browser - whichever is quicker.
  5. Press the P key to start the simulation.
Yard Map:
Yard map
Tasks:
  1. Move the loco out of the depot and run tender first past Terowie Station to the Goods Transfer Sidings.
  2. Couple the loco to the rake of MTW flat wagons stored on the northern (Peterborough) end of Siding 2.
  3. Take the MTW flat wagons to the Goods Gantry Narrow Gauge to be loaded.
  4. After loading take the wagons back to the Goods Transfer Sidings and store them on Siding 1.
  5. Couple the loco to the rake of QLX wagons on Siding 2.
  6. Take the QLX wagons to the Goods Transfer Narrow Gauge shed and load.
  7. After loading move the wagons onto Siding 2.
  8. The two rakes of loaded wagons on Siding 1 and Siding 2 must be split and recombined into two consists according to their destinations. The destinations, Peterborough and Gladstone, are shown in the name of each wagon. All the Gladstone wagons are to be placed into one consist and the Peterborough wagons into the other consist.
  9. Combine the two consists into one consist with the Peterborough wagons at the front (Peterborough) end the DB Guard Van at the rear of the Gladstone wagons.
  10. Move the combined consist onto the Loop road in the main Terowie Yard.
  11. Return the loco to its starting position on Terowie Depot.
Driving Notes:
  • You have permission to pass semaphore signals at stop provided you are satisfied that the road ahead is clear.
Top


Personal tools